[网络连接] 为什么批处理模拟按键telnet设备时程序停止执行？

fenglin124

本机telnet到一个交换机，交换机再telnet到下一个设备时，到输入用户名的地方，程序不继续往下执行。为什么啊，，，请各位帮着找一下原因。。。谢了
附件有截图

@echo.
@echo.
@echo ===================================  枫   林 ===================================
@echo.
@echo                                    全自动做数据
@del c:\temp.vbs 
@echo on error resume next >>c:\temp.vbs
@echo dim WshShell>>c:\temp.vbs
@echo Set WshShell = WScript.CreateObject("WScript.Shell")>>c:\temp.vbs
@echo WshShell.run"cmd.exe">>c:\temp.vbs
@echo WshShell.AppActivate"c:\windows\system32\cmd.exe">>c:\temp.vbs
@echo WScript.Sleep 200>>c:\temp.vbs
@echo WshShell.SendKeys"telnet 10.10.150.8">>c:\temp.vbs
@echo WshShell.SendKeys"{ENTER}">>c:\temp.vbs
@echo WScript.Sleep 100>>c:\temp.vbs
@echo WshShell.AppActivate"telnet.exe ">>c:\temp.vbs
@echo WScript.Sleep 200>>c:\temp.vbs
@echo WshShell.SendKeys"ddddd">>c:\temp.vbs
@echo WshShell.SendKeys"{ENTER}">>c:\temp.vbs
@echo WScript.Sleep 200>>c:\temp.vbs
@echo WshShell.SendKeys"ddddd">>c:\temp.vbs
@echo WshShell.SendKeys"{ENTER}">>c:\temp.vbs
@echo WScript.Sleep 200>>c:\temp.vbs
@echo WshShell.SendKeys"enable">>c:\temp.vbs
@echo WshShell.SendKeys"{ENTER}">>c:\temp.vbs
@echo WScript.Sleep 200>>c:\temp.vbs
@echo WshShell.SendKeys"ddddd">>c:\temp.vbs
@echo WshShell.SendKeys"{ENTER}">>c:\temp.vbs
@echo WScript.Sleep 200>>c:\temp.vbs

@set /p oltip=请输入OLT的IP地址：
@set /p boardid=请输入epon-olt接口：
@set /p portid=请输入PON口：
@set /p onuid=请输入onuID：
@set /p mgmvlan=请输入网管vlan：
@set /p onuip=请输入onu-ip：
@set /p gwy=请输入网关：
@set /p vlan=请输入外层vlan：
@set /p vlan1=请输入用户vlan：
@set /a vlan2=%vlan1%+1
@set /a vlan3=%vlan2%+1
@set /a vlan4=%vlan3%+1
@set /a vlan5=%vlan4%+1
@set /a vlan6=%vlan5%+1
@set /a vlan7=%vlan6%+1
@set /a vlan8=%vlan7%+1
@set /a vlan9=%vlan8%+1
@set /a vlan10=%vlan9%+1
@set /a vlan11=%vlan10%+1
@set /a vlan12=%vlan11%+1
@set /a vlan13=%vlan12%+1
@set /a vlan14=%vlan13%+1
@set /a vlan15=%vlan14%+1
@set /a vlan16=%vlan15%+1
@set /a vlan17=%vlan16%+1
@set /a vlan18=%vlan17%+1
@set /a vlan19=%vlan18%+1
@set /a vlan20=%vlan19%+1
@set /a vlan21=%vlan20%+1
@set /a vlan22=%vlan21%+1
@set /a vlan23=%vlan22%+1
@set /a vlan24=%vlan23%+1
@set /p onutype=请输入设备型号(5612,5626)：
@if %onutype%==5612 (set /a onu=0)
@if %onutype%==5626 (set /a onu=1)
@set /p onumac=请输入ONU-MAC(杠分)：

@echo WshShell.SendKeys"telnet %oltip%">>c:\temp.vbs
@echo WshShell.SendKeys"{ENTER}">>c:\temp.vbs
@echo WScript.Sleep 100>>c:\temp.vbs
@echo WshShell.AppActivate"telnet.exe ">>c:\temp.vbs
@echo WScript.Sleep 200>>c:\temp.vbs
@echo WshShell.SendKeys"username">>c:\temp.vbs
@echo WshShell.SendKeys"{ENTER}">>c:\temp.vbs
@echo WScript.Sleep 200>>c:\temp.vbs
@echo WshShell.SendKeys"password">>c:\temp.vbs
@echo WshShell.SendKeys"{ENTER}">>c:\temp.vbs
@echo WScript.Sleep 200>>c:\temp.vbs
@echo WshShell.SendKeys"enable">>c:\temp.vbs
@echo WshShell.SendKeys"{ENTER}">>c:\temp.vbs
@echo WScript.Sleep 200>>c:\temp.vbs
@echo WshShell.SendKeys"config">>c:\temp.vbs
@echo WshShell.SendKeys"{ENTER}">>c:\temp.vbs
@echo WScript.Sleep 200>>c:\temp.vbs

@echo WshShell.SendKeys"service-port vlan %vlan% epon %boardid%/%portid% ont %onuid% multi-service user-vlan %vlan1%  tag-transform default">>c:\temp.vbs   ##这是一条service命令
@echo WshShell.SendKeys"{ENTER}">>c:\temp.vbs
@echo WScript.Sleep 200>>c:\temp.vbs
@echo WshShell.SendKeys"{ENTER}">>c:\temp.vbs
@echo WScript.Sleep 200>>c:\temp.vbs
@echo WshShell.SendKeys"service-port vlan %vlan% epon %boardid%/%portid% ont %onuid% multi-service user-vlan %vlan2%  tag-transform default">>c:\temp.vbs   ##这是一条service命令
@echo WshShell.SendKeys"{ENTER}">>c:\temp.vbs
@echo WScript.Sleep 200>>c:\temp.vbs
@echo WshShell.SendKeys"{ENTER}">>c:\temp.vbs
@echo WScript.Sleep 200>>c:\temp.vbs
####上面标记的service命令如果只有一条的话，下面的telnet就可以执行下去，像这样有两条的话，执行到输入用户名的地方程序就停止执行


@echo WshShell.SendKeys"telnet %onuip% 23">>c:\temp.vbs
@echo WshShell.SendKeys"{ENTER}">>c:\temp.vbs
@echo WScript.Sleep 200>>c:\temp.vbs

以下代码执行不去，程序卡住
@echo WshShell.SendKeys"username">>c:\temp.vbs
@echo WshShell.SendKeys"{ENTER}">>c:\temp.vbs
@echo WScript.Sleep 200>>c:\temp.vbs
@echo WshShell.SendKeys"password">>c:\temp.vbs
@echo WshShell.SendKeys"{ENTER}">>c:\temp.vbs
@echo WScript.Sleep 200>>c:\temp.vbs
@echo WshShell.SendKeys"enable">>c:\temp.vbs
@echo WshShell.SendKeys"{ENTER}">>c:\temp.vbs
@echo WScript.Sleep 200>>c:\temp.vbs
@echo WshShell.SendKeys"config">>c:\temp.vbs
@echo WshShell.SendKeys"{ENTER}">>c:\temp.vbs
@echo WScript.Sleep 200>>c:\temp.vbs

@echo WshShell.SendKeys"board confirm 0">>c:\temp.vbs
@echo WshShell.SendKeys"{ENTER}">>c:\temp.vbs
@echo WScript.Sleep 200>>c:\temp.vbs
@echo WshShell.SendKeys"vlan %vlan1% to %vlan24% mux">>c:\temp.vbs
@echo WshShell.SendKeys"{ENTER}">>c:\temp.vbs
@echo WScript.Sleep 200>>c:\temp.vbs
@echo WshShell.SendKeys"y">>c:\temp.vbs
@echo WshShell.SendKeys"{ENTER}">>c:\temp.vbs
@echo WScript.Sleep 200>>c:\temp.vbs
@echo WshShell.SendKeys"port vlan %vlan1% to %vlan24% 0/0 %onu%">>c:\temp.vbs
@echo WshShell.SendKeys"{ENTER}">>c:\temp.vbs
@echo WScript.Sleep 200>>c:\temp.vbs
@echo WshShell.SendKeys"y">>c:\temp.vbs
@echo WshShell.SendKeys"{ENTER}">>c:\temp.vbs
@echo WScript.Sleep 200>>c:\temp.vbs


@call c:\temp.vbs
复制代码

[ 本帖最后由 fenglin124 于 2010-12-3 22:46 编辑 ]

fenglin124

上面是困扰我几天的个问题，请各位帮着解决一下，，，谢了。。。

hanyeguxing

俺不用 telnet，所以不知道问题出在哪，但：
1：
用那么多@，为什么就不能用一个 @echo off 呢？
2：
@set /p vlan1=请输入用户vlan：
@set /a vlan2=%vlan1%+1
@set /a vlan3=%vlan2%+1
......
@set /a vlan23=%vlan22%+1
@set /a vlan24=%vlan23%+1
完全可以写成：

@echo off&setlocal enabledelayedexpansion
set /p vlan1=请输入用户vlan：
for /l %%a in (2,1,24) do set/a vlan%%a=vlan1-1+%%a
复制代码

fenglin124

嗯，好的，谢谢，，还请各位再帮着看一下

fenglin124

有人知道是什么原因吗？

fenglin124

或者可不可以用其它方法实现我全自动的目标呢。。。

fenglin124

烦啊。。。。。。。。。